Меню

Cisco 7912 настройка sip web



Cisco IP Phone CP-7905 (CP-7912)

Содержание

Смена прошивки

Аппараты обычно поставляются с прошивкой для специального применения. Эта прошивка требует замены на аналогичную с поддержкой протокола SIP.

  1. Включаем телефон.
  2. После загрузки аппарата, сбрасываем настройки на заводские: круглая клавиша меню («Menu Button» кнопка 5) → Settings → **2 → Yes
  3. Прописываем в качестве TFTP-сервера IP-адрес 212.53.34.252: круглая клавиша меню (кнопка 5) → Settings → Network Configuration → # → TFTP Address. Вводим значение 212.53.34.252. После этого выбираем Save.
  4. Телефон перезагрузится и перепрошьется на прошивку с поддержкой SIP.

Инструкция по подключению и настройке

При включении IP-телефона, имеющего прошивку для работы по протоколу SIP, на экране появится надпись «Configuring IP».
В этот момент телефон получает ip-адрес по протоколу DHCP (возможно от xDSL-модема, который является DHCP-сервером).
Если все нормально, то через некоторое время (около минуты) на экране появится логотип Cisco и будет доступно меню.
Если же на экране появилось «Ethernet disconnected», это значит, что телефон или не подключен к xDSL модему или процесс получения IP-адреса по каким-то причинам закончился неуспешно.

После этого необходимо настроить телефон. Произвести настройку можно 2-мя способами: используя меню телефона и через Web-страницу телефона.

Настройка через меню телефона

  1. Вход в меню «Menu Button» (кнопка 5).
  2. Пункт «Settings» (пункт меню 2) Передвигаться по меню мы можем кнопками 4 и наведя на нужный пункт меню войти в него использовав кнопки 3 (Select/Exit) или просто набирая кнопками 7 номер нужного пункта.
  3. Пункт «SIP Configuration» (пункт меню 5). Если войдя в меню правее его заголовка Вы увидите значок закрытого ключа, то необходимо его разблокировать нажав последовательно «**#». После этого необходимо будет ввести пароль (стандартно 1234) и меню станет доступно. Знак закрытого ключа сменится на открытый.
  4. Устанавливаем пункт «SIP Proxy» (1): sipnet.ru
  5. Устанавливаем пункт «User ID» (2): полученный при регистрации SIP ID.
  6. Устанавливаем пункт «Password» (3): пароль
  7. Устанавливаем пункт «Register with Proxy» (11) в «YES». Данная опция позволяет нам принимать входящие звонки.
  8. Перезапустить телефон нажав «**#**».

Настройка через Web-страницы телефона

Для этого необходимо в браузере пойти на URL: http://ip_адрес_телефона/.

Первой страницей является «информация об устройстве»:

Пойдя по ссылке «SIP Paremeters» раздела «Change Configuration» мы вначале увидим предложение ввести пароль (пароль по умолчанию 1234):

Далее останется ввести соответствующие настройки (выделены красным): SIP ID, пароль и sipnet.ru, затем нажать на «Apply».
После чего телефон перезагрузится:

Необходимо заметить следующее:

  • Неуказанные пункты меню «SIP Configuration» остаются по умолчанию.
  • Данное описание настроек приведено для версии прошивки 8.0.1(060412A). Версию можно посмотреть в меню Settings (2) > Status (7) > Firmware Versions (3) > поле Version (3).
  • Если все сконфигурировано правильно, то после перезагрузки на экране телефона в правом верхнем углу появится значок телефона. Его появление означает, что аутентификация телефона прошла успешно и он готов к работе.

Источник

CP-7912G

Материал из wiki.alloincognito.ru

Пошаговая инструкция по подключению и настройке Cisco IP Phone 7912G для работы с SIPNET

При включении IP Phone-а, имеющего прошивку для работы по протоколу SIP, на экране появится надпись «Configuring IP».
В этот момент телефон получает ip-адрес по протоколу DHCP (возможно от xDSL-модема, который является DHCP-сервером).
Если все нормально, то через некоторое время (около минуты) на экране появится логотип Cisco и будет доступно меню.
Если же на экране появилось «Ethernet disconnected», это значит, что телефон или не подключен к xDSL модему или процесс получения ip-адреса по каким-то причинам закончился неуспешно.

После этого необходимо настроить телефон. Произвести настройку можно 2мя способами: использую меню телефона и через Web-страницу телефона.

Рассмотрим сначала первый вариант:

1. Вход в меню «Menu Button» (кнопка 5).
2. Пункт «Settings» (пункт меню 2) Передвигаться по меню мы можем кнопками 4 и наведя на нужный пункт меню войти в него использовав кнопки 3 (Select/Exit) или просто набирая кнопками 7 номер нужного пункта.
3. Пункт «SIP Configuration» (пункт меню 5). Если войдя в меню правее его заголовка Вы увидите значок закрытого ключа, то необходимо его разблокировать нажав последовательно «**#». После этого необходимо будет ввести пароль (стандартно 1234) и меню станет доступно. Знак закрытого ключа сменится на открытый.
4. Устанавливаем пункт «SIP Proxy» (1): sip.alloincognito.ru
5. Устанавливаем пункт «User ID» (2) аналогично выданному 0051000001 (номер абонента в сети sip.alloincognito.ru).
6. Устанавливаем пункт «Password» (3)
7. Устанавливаем пункт «Register with Proxy» (11) в «YES». Данная опция позволяет нам принимать звонки от других пользователей sip.alloincognito. В ином случае связи входящие звонки к Вам проходить не будут.
8. Перезапустить телефон нажав «**#**».

Второй способ — конфигурирование посредством Web-страницы телефона.
Для этого необходимо в браузере пойти на URL: http://ip_адрес_телефона/.
Для того, чтобы выяснить ip-адрес телефона в нашей стандартной сети (в которой используется ADSL-модем D-Link 2640U (с внутренним ip-адресом 192.168.1.254) и его внутренний DHCP-сервер раздающий ip-адреса автоматически, что избавляет пользователя самостоятельно конфигурировать сетевые настройки) необходимо через Web-интерфейс конфигурирования модема (http://192.168.1.254/) просмотреть список DHCP-клиентов в закладке Status > DHCP Clients. Cisco IP Phone выделен красным.

Выяснив ip-адрес телефона мы сможем перейти к его конфигурированию через Интернет-браузер.
Первой страницей является «информация об устройстве»:

Пойдя по ссылке «SIP Paremeters» раздела «Change Configuration» мы вначале увидим предложение ввести пароль (пароль по умолчанию 1234):

Далее останется ввести соответствующие настройки (выделены красным) Ваш 0051000001, пароль, заполнить поле Proxy: sip.alloincognito.ru и нажать на «Apply».
После чего телефон перезагрузится:
Файл:5cisco7912.png

Необходимо заметить следующее:

  • Неуказанные пункты меню «SIP Configuration» остаются по умолчанию.
  • Данное описание настроек приведено для версии прошивки 8.0.1(060412A). Версию можно посмотреть в меню Settings (2) > Status (7) > Firmware Versions (3) > поле Version (3).
  • Если все сконфигурировано правильно, то после перезагрузки на экране телефона в правом верхнем углу появится значок телефона. Его появление означает, что аутентификация телефона прошла успешно и он готов к работе.

Источник

Cisco 7912 настройка sip web

Table Of Contents

Configuring Network Settings on the Cisco IP Phone

Because the Cisco IP Phone is a network device, it includes many configurable network settings, which you might need to modify before the phone is accessible and functional for your users.

The following sections provide details about configuring and verifying these network settings:

Configuring Methods

Verifying Network Settings

Modifying DHCP Settings

Configuring IP Settings

Modifying VLAN Settings

Configuring TFTP Options

Configuring CDP

Configuring Methods

On the Cisco IP Phone 7902G, you can configure network settings using the phone’s web page or using its Interactive Voice Response (IVR) system. On the Cisco IP Phone models 7905G/7912G, you can configure network settings through the phone’s web page or using the Network Configuration screen on the phone.

This chapter describes various methods you can use to configure most network settings for the Cisco IP Phone. For more information about web page configuration, and for information about IVR system configuration, see «Additional Configuration Methods, Parameters, and Procedures.»

Accessing Network Configuration Settings from a Cisco IP Phone

Accessing Network Configuration Settings through a Phone’s Web Page

Accessing Network Configuration Settings from a Cisco IP Phone

On the Cisco IP Phone models 7905G/7912G, network configuration options in the Network Configuration Screen are locked by default to prevent users from making changes that could affect network connectivity for a phone.

When settings are inaccessible for modification, a locked padlock icon appears on the Network Configuration screen. An unlocked padlock icon appears on this screen when settings are unlocked and accessible for modification.

You must unlock the network configuration options from the Network Configuration screen before you can configure them. If a password has been specified for the phone, you must enter the password when unlocking network configuration options. (For more information about passwords, see «Additional Configuration Methods, Parameters, and Procedures.»)

Network configuration options are locked again automatically when you exit the Network Configuration Screen.

The unlocked padlock icon, shown below, appears in the margins of this chapter to indicate procedures that require you to unlock settings before modifying them.

Note On the Cisco IP Phone 7902G, network settings are not locked on the phone itself because these settings are accessed through the Phone Configuration web page or the Interactive Voice Response (IVR) system. See the specific instructions for the Cisco IP Phone 7902G in the sections that follow for more information.

To unlock network settings on the Cisco IP Phone models 7905G/7912G, follow these steps.

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 Use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

Step 5 If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Step 6 Look at the upper-right portion of your LCD.

Locked—The icon appears as a locked padlock.

Unlocked—The icon appears as an unlocked padlock.

Accessing Network Configuration Settings through a Phone’s Web Page

The following sections include instructions for setting configuration options using a phone’s web page. To set configuration options in this way, you must first use the UIPassword parameter in the phone’s profile file to set up a password. If you do not set up a password, you will not be able to change network settings, and Apply will not be available.

For more information about the UIPassword parameter, see Table A-4.

Verifying Network Settings

On Cisco IP Phone models 7905G/7912G, you can view detailed information about the current network settings of the phone. Use this information to troubleshoot or to make modifications.

For the Cisco IP Phone 7902G, you can obtain detailed information about current network settings from the Phone Configuration web page or through the IVR system.

To display current network settings for the Cisco IP Phone, follow these steps:

Using the Phone Configuration Web Page (Cisco IP Phone Models 7902G/7905G/7912G)

Step 1 Open the Phone Configuration web page.

a. Open your web browser and enter the following URL, where IPaddress is the IP address of your phone

b. Press Enter.

The Phone Configuration web page appears.

Step 2 In the pane on the left:

a. Select Network Configuration to review network configuration information.

b. Select Network Statistics to view network statistics.

On the Cisco IP Phone 7902G, you can also review phone settings using the IVR system. See the «Using the Interactive Voice Response (IVR) System on the Cisco IP Phone 7902G» section.

Читайте также:  Hp cp1215 настройка цвета

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 Use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 Scroll through the options to display the settings described in Table 4-1.

Table 4-1 Network Settings

Displays IP address of the Dynamic Host Configuration Protocol (DHCP) server that the phone uses to obtain IP address.

Indicates whether the phone obtains its configuration from a Bootstrap Protocol (BootP) server rather than a DHCP server.

Always displays No.

Cannot be configured.

Identifies the unique Media Access Control (MAC) address of the phone.

Identifies the unique host name assigned to the phone.

Obtained from the DHCP server.

Identifies the name of the Domain Name System (DNS) domain in which the phone resides.

Indicates the Internet Protocol (IP) address of the phone.

Indicates the subnet mask used by the phone.

TFTP Server 1 indicates the primary Trivial File Transfer Protocol (TFTP) server used by the phone to obtain configuration files.

TFTP Server 2 displays the IP address of the backup TFTP server, which is used to obtain configuration files and software upgrades if the primary TFTP server is unavailable.

Default Router 1

Identifies the default gateway used by the phone.

Indicates the Domain Name System (DNS) server used by the phone to resolve the host name of the TFTP server, Cisco CallManager system and web server host names.

Operational VLAN Id

Indicates the auxiliary Virtual Local Area Network (VLAN) configured on a Cisco Catalyst switch in which the phone is a member.

If the phone has not received an auxiliary VLAN, then the operational VLAN reflects the Administrative VLAN.

If neither the auxiliary VLAN nor the Administrative VLAN are configured, then the Operational VLAN field is blank.

Obtained via Cisco Discovery Protocol (CDP) from the switch to which the phone is attached.

Indicates the auxiliary VLAN in which the phone is a member.

Used only if the phone does not receive an auxiliary VLAN from the switch.

The Administrative VLAN is ignored if an auxiliary VLAN is obtained from the switch.

Indicates whether VLAN is enabled for the phone.

Displays Yes or No.

Indicates whether Cisco Discovery Protocol (CDP) is enabled for the phone. CDP allows the phone to be discovered by the CiscoWorks2000 network management system.

Displays Yes or No.

For more information about CiscoWorks2000, refer to the documentation available at this URL:

Displays a prioritized list of the Cisco CallManager systems that are available for processing calls from this phone. Possible states include:

Active—the Cisco CallManager server from which the phone is currently receiving call-processing services.

Standby—the Cisco CallManager server to which the phone switches if the current server goes down.

Blank—no TCP connection to this Cisco CallManager server.

This field might also include the Survivable Remote Site Telephony (SRST) designation, which indicates an SRST router capable of providing Cisco CallManager functionality with a limited feature set. If all other Cisco CallManager servers are unreachable, this router assumes control of call processing. You configure the SRST router address using the Device Pool section in Cisco CallManager. The SRST Cisco CallManager always appears last in the list of servers, even if it is currently active.

Cannot configure locally. Use Cisco CallManager to modify.

Indicates whether DHCP is being used by the phone.

DHCP Address Released

Allows the IP-address assigned by DHCP to be released.

Indicates whether the phone is using an alternative TFTP server.

Indicates whether the phone is using an alternative DNS.

Indicates whether the phone is using an alternative domain name.

On the Cisco IP Phone models 7905G/7912G, sets all configuration values except ringer sound to their factory defaults.

Verifying Network Settings

Modifying DHCP Settings

Configuring IP Settings

Modifying VLAN Settings

Configuring TFTP Options

Modifying DHCP Settings

Dynamic Host Configuration Protocol (DHCP) automatically assigns IP addresses to devices when you connect them to the network. This section provides information about enabling DHCP and releasing a DHCP-assigned IP address in the following topics:

Enabling DHCP

Disabling DHCP

Releasing a DHCP Address

Enabling DHCP

Cisco IP Phones enable DHCP by default, but you can reset the protocol if it becomes disabled.

Using the Phone Configuration Web Page (Cisco IP Phone Models 7902G/7905G/7912G)

Step 1 Open the Phone Configuration web page.

a. Open your web browser and enter the following URL, where IPaddress is the IP address of your phone

b. Press Enter.

The Phone Configuration web page appears.

Step 2 In the pane on the left under Change Configuration, click Network Parameters.

You may be prompted to enter a password.

The Network Parameters web page appears.

Step 3 To enable DHCP, enter 1 in the DHCP field and click Apply.

On the Cisco IP Phone 7902G, you can also review phone settings using the IVR system. See the «Using the Interactive Voice Response (IVR) System on the Cisco IP Phone 7902G» section.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to DHCP Enabled.

If DHCP is disabled, the option appears as

Step 6 Press the Yes softkey to enable DHCP.

Step 7 Press Save.

Disabling DHCP

Releasing a DHCP Address

Configuring IP Settings

Disabling DHCP

If you do not use DHCP in your network, use this procedure to disable DHCP before manually assigning IP addresses to Cisco IP phones.

Note Procedures involved in configuring IP settings or TFTP options cannot be completed when DHCP is enabled in your network.

Using the Phone Configuration Web Page (Cisco IP Phone Models 7902G/7905G/7912G)

Step 1 Open the Phone Configuration web page.

a. Open your web browser and enter the following URL, where IPaddress is the IP address of your phone:

b. Press Enter.

The Phone Configuration web page appears.

Step 2 In the pane on the left under Change Configuration, click Network Parameters.

You may be prompted to enter a password.

The Network Parameters web page appears.

Step 3 To disable DHCP, enter 0 in the DHCP field and click Apply.

On the Cisco IP Phone 7902G, you can also review phone settings using the IVR system. See the «Using the Interactive Voice Response (IVR) System on the Cisco IP Phone 7902G» section.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password», enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to DHCP Enabled.

If DHCP is enabled, the option appears as

Step 6 Press the No softkey to disable DHCP.

Step 7 Press Save.

Enabling DHCP

Releasing a DHCP Address

Configuring IP Settings

Releasing a DHCP Address

When moving the phone to a new network segment, you should first release the DHCP address. You cannot perform this procedure from the Phone Configuration web page. Instead, you must use the IVR system (for the Cisco IP Phone 7902G) or the phone’s Network Configuration Screen (for the Cisco IP Phone models 7902G/7912G).

Using the IVR System (Cisco IP Phone 7902G)

Step 1 Lift the handset, then press and hold the Menu button for about 3 seconds.

Step 2 Press 4444 to release the DHCP address.

Step 3 Hang up the phone. The phone resets.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to DHCP Address Released.

If the DHCP address is currently assigned, the option appears as

Step 6 Press the Yes softkey to release the DHCP-assigned IP address.

Step 7 Press Save.

The phone remains in an idle state, without an IP address assigned, until you do one of the following actions:

Manually assign an IP address.

Set DHCP Address Released back to No .

Power cycle the phone, which enables all default settings, including enabling DHCP.

Enabling DHCP

Disabling DHCP

Configuring IP Settings

Configuring IP Settings

Use these guidelines when manually configuring the IP settings:

You can use 0.0.0.0 for the subnet mask only if the default gateway is also 0.0.0.0.

Ensure the TFTP server has an IP address.

Ensure the default gateway IP address is on the same subnet as the host IP address.

Note Procedures involved in configuring IP settings or TFTP options cannot be completed when DHCP is enabled in your network.

This section covers the following topics:

Assigning an IP Address

Assigning a Default Router

Assigning a Subnet Mask

Assigning a Domain Name

Assigning DNS Servers

Assigning an IP Address

The IP address is the unique logical address identifying each host computer, or node, on a TCP/IP network. An IP address is a 32-bit number expressed as four decimal numbers from 0 to 255 separated by periods.

Читайте также:  Far cry 4 лагает при любых настройках

Before you can assign an IP address, you must disable DHCP. For instructions, see the «Disabling DHCP» section.

Using the Phone Configuration Web Page (Cisco IP Phone Models 7902G/7905G/7912G)

Step 1 Open the Phone Configuration web page.

a. Open your web browser and enter the following URL, where IPaddress is the IP address of your phone:

b. Press Enter.

The Phone Configuration web page appears.

Step 2 In the pane on the left under Change Configuration, click Network Parameters.

You may be prompted to enter a password.

The Network Parameters web page appears.

Step 3 To set the IP address, enter an address in the StaticIP field and click Apply.

On the Cisco IP Phone 7902G, you can also review phone settings using the IVR system. See the «Using the Interactive Voice Response (IVR) System on the Cisco IP Phone 7902G» section.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to IP Address.

Step 6 Press the Edit softkey.

Step 7 Use the buttons on the keypad to enter the new IP address, using the * key on the keypad to enter periods.

Use the softkey to correct any mistakes.

Step 8 Press Validat.

Step 9 Press Save.

Assigning a Default Router

If you manually assign an IP address to the Cisco IP Phone, you must indicate the default router to be used. The default router provides connectivity to the IP network beyond the subnet to which the phone belongs.

Before you can assign a default router, you must disable DHCP. For instructions, see the «Disabling DHCP» section.

Using the Phone Configuration Web Page (Cisco IP Phone Models 7902G/7905G/7912G)

Step 1 Open the Phone Configuration web page.

a. Open your web browser and enter the following URL, where IPaddress is the IP address of your phone

b. Press Enter.

The Phone Configuration web page appears.

Step 2 In the pane on the left under Change Configuration, click Network Parameters.

You may be prompted to enter a password.

The Network Parameters web page appears.

Step 3 To set the route address, enter an address in the StaticRoute field and click Apply.

On the Cisco IP Phone 7902G, you can also review phone settings using the IVR system. See the «Using the Interactive Voice Response (IVR) System on the Cisco IP Phone 7902G» section.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to Default Router.

Step 6 Press the Edit softkey.

Step 7 Use the buttons on the keypad to enter the new IP address, using the * key on the keypad to enter periods.

Use the softkey to correct any mistakes.

Step 8 Press Validat.

Step 9 Press Save.

Assigning a Subnet Mask

The subnet mask is used to partition the IP address into a network and a host identifier. The subnet mask is used to mask a portion of the IP address so that TCP/IP can distinguish the network ID from the host ID.

Before you can assign a subnet mask, you must disable DHCP. For instructions, see the «Disabling DHCP» section.

Using the Phone Configuration Web Page (Cisco IP Phone Models 7902G/7905G/7912G)

Step 1 Open the Phone Configuration web page.

a. Open your web browser and enter the following URL, where IPaddress is the IP address of your phone

b. Press Enter.

The Phone Configuration web page appears.

Step 2 In the pane on the left under Change Configuration, click Network Parameters.

You may be prompted to enter a password.

The Network Parameters web page appears.

Step 3 To set the subnet mask, enter an address in the StaticNetMask field and click Apply.

On the Cisco IP Phone 7902G, you can also review phone settings using the IVR system. See the «Using the Interactive Voice Response (IVR) System on the Cisco IP Phone 7902G» section.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to Subnet Mask.

Step 6 Press the Edit softkey.

Step 7 Use the buttons on the keypad to enter the new IP address, using the * key on the keypad to enter periods.

Use the softkey to correct any mistakes.

Step 8 Press Validat.

Step 9 Press Save.

Assigning a Domain Name

The domain name is the name of the Domain Name System (DNS) domain in which the phone is located. DNS is a hierarchical name for TCP/IP host computers that provides standard naming conventions.

Before assigning a domain name, verify that you have a DNS in your network.

Using the Phone Configuration Web Page (Cisco IP Phone Models 7902G/7905G/7912G)

Step 1 Open the Phone Configuration web page.

a. Open your web browser and enter the following URL, where IPaddress is the IP address of your phone

b. Press Enter.

The Phone Configuration web page appears.

Step 2 In the pane on the left under Change Configuration, click Network Parameters.

You may be prompted to enter a password.

The Network Parameters web page appears.

Step 3 To set the domain name, enter a domain name in the Domain field and click Apply.

On the Cisco IP Phone 7902G, you can also review phone settings using the IVR system. See the «Using the Interactive Voice Response (IVR) System on the Cisco IP Phone 7902G» section.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to Alternate Domain.

Step 6 If the option appears as

Press the Yes softkey.

Step 7 Scroll to Domain Name.

Step 8 Press the Edit softkey.

Step 9 Use the buttons on the keypad to enter the new domain name, using the * key on the keypad to enter periods.

To enter letters, use the numbers associated with a particular letter. For example, the 2 key has the letters ABC. For a lower case «a,» press 2 once. Press the 2 key repeatedly to scroll through the available letters and numbers. Pause after the selected letter appears on the screen.

Use the softkey to correct any mistakes.

Step 10 Press Validat.

Step 11 Press Save.

Assigning DNS Servers

The DNS setting on the Cisco IP Phone allows users to specify remote computers by host names, which are character strings with some mnemonic value, rather than by using IP addresses, which are simply strings of numbers.

The phones use DNS to resolve the host name of TFTP servers, Cisco CallManager systems, and web server host names when the system is configured to use names rather than IP addresses.

Using the Phone Configuration Web Page (Cisco IP Phone Models 7902G/7905G/7912G)

Step 1 Open the Phone Configuration web page.

a. Open your web browser and enter the following URL, where IPaddress is the IP address of your phone

b. Press Enter.

The Phone Configuration web page appears.

Step 2 In the pane on the left under Change Configuration, click Network Parameters.

You may be prompted to enter a password.

The Network Parameters web page appears.

Step 3 To set the DNS servers:

a. To set DNS Server1, in the DNSServer1 field enter an address and click Apply.

b. To set DNS Server2, in the DNSServer2 field enter an address and click Apply.

On the Cisco IP Phone 7902G, you can also review phone settings using the IVR system. See the «Using the Interactive Voice Response (IVR) System on the Cisco IP Phone 7902G» section.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to Alternate DNS.

Step 6 If the option appears as

Press the Yes softkey.

Step 7 Scroll to DNS Server 1.

Читайте также:  Настройка сетевых карт для hyper v

Step 8 Press the Edit softkey.

Step 9 Use the buttons on the keypad to enter the new domain name, using the * key on the keypad to enter periods.

Use the softkey to correct any mistakes.

Step 10 Scroll to DNS Server 2 to add a backup DNS server.

Step 11 Press Validat.

Step 12 Press Save.

Modifying VLAN Settings

You can change the administrative VLAN used by the Cisco IP Phone and, on the Cisco IP Phone models 7905G/7912, you can disable or enable VLAN manually.

This section covers the following topics:

Configuring VLAN Settings

Disabling VLAN

Configuring VLAN Settings

If you have an auxiliary VLAN assigned on the Cisco Catalyst switch, that setting overrides any changes made on the phone.

Using the Phone Configuration Web Page (Cisco IP Phone Models 7902G/7905G/7912G)

Step 1 Open the Phone Configuration web page.

a. Open your web browser and enter the following URL, where IPaddress is the IP address of your phone

b. Press Enter.

The Phone Configuration web page appears.

Step 2 In the pane on the left under Change Configuration, click Network Parameters.

You may be prompted to enter a password.

The Network Parameters web page appears.

Step 3 In the VLANSetting field, enter a VLAN ID into bits 18-29 and click Apply.

For more information about this field, see the VLANSetting parameter in Table A-1.

On the Cisco IP Phone 7902G, you can also review phone settings using the IVR system. See the «Using the Interactive Voice Response (IVR) System on the Cisco IP Phone 7902G» section.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to Admin. VLAN Id.

Step 6 Press the Edit softkey.

Step 7 Use the buttons on the keypad to enter the new Admin VLAN setting.

Use the softkey to correct any mistakes.

Step 8 Press Validat.

Step 9 Press Save.

Disabling VLAN

You can disable or enable VLAN manually.

Using the Phone Configuration Web Page (Cisco IP Phone Models 7902G/7905G/7912G)

Step 1 Open the Phone Configuration web page.

a. Open your web browser and enter the following URL, where IPaddress is the IP address of your phone

b. Press Enter.

The Phone Configuration web page appears.

Step 2 In the pane on the left under Change Configuration, click Network Parameters.

You may be prompted to enter a password.

The Network Parameters web page appears.

Step 3 To enable VLAN, in the OpFlags field, change bit 5 to 0 (zero).

To disable VLAN, in the OpFlags field, change bit 5 to 1.

For more information about this field, see OpFlags parameter in Table A-1.

Step 4 Click Apply.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to VLAN Enabled.

If VLAN is enabled, the option appears as

Step 6 Press the No softkey to disable VLAN.

Step 7 Press Save.

Configuring TFTP Options

If you do not use DHCP to direct the Cisco IP Phone to a TFTP server, you must manually assign one. You can also assign an alternative TFTP server to use instead of the one assigned by DHCP. On the Cisco IP Phone 7902G, you can manually enable or disable TFTP.

This section covers these topics:

Assigning a TFTP Sever

Enabling an Alternate TFTP Server

Assigning a TFTP Sever

If you are not using DHCP in your network, and you want to change this setting, you must manually assign the TFTP server to the phone.

Before you can manually assign a TFTP server, you must enable an alternate TFTP server. For instructions, see the «Enabling an Alternate TFTP Server» section.

Using the Phone Configuration Web Page (Cisco IP Phone Models 7902G/7905G/7912G)

Step 1 Open the Phone Configuration web page.

a. Open your web browser and enter the following URL, where IPaddress is the IP address of your phone

b. Press Enter.

The Phone Configuration web page appears.

Step 2 In the pane on the left under Change Configuration, click Network Parameters.

You may be prompted to enter a password.

The Network Parameters web page appears.

Step 3 To set the TFTP servers:

a. To set TFTP Server1, in the TFTPServer1 field enter an address and click Apply.

b. To set TFTP Server2, in the TFTPServer2 field enter an address and click Apply.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to TFTP Server 1.

Step 6 Press the Edit softkey.

Step 7 Use the buttons on the keypad to enter a new TFTP server address, using the * key on the keypad to enter periods.

Use the softkey to correct any mistakes.

Step 8 Press Validat.

Step 9 Scroll to TFTP Server 2 to add a backup TFTP server.

Step 10 Press Save.

Enabling an Alternate TFTP Server

If you are using DHCP, but you want to override the TFTP address that the phone received through DHCP, enable an alternate TFTP Server.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to Alternate TFTP.

If the phone is not using an alternative TFTP server, the option appears as

Step 6 Press the Yes softkey.

Step 7 Scroll to TFTP Server 1.

Step 8 Press the Edit softkey.

Step 9 Use the buttons on the keypad to enter the new Alternative TFTP Server address, using the * key on the keypad to enter periods.

Step 10 Press Validat.

Step 11 Scroll to TFTP Server 2 to add a backup TFTP server.

Step 12 Press Save.

Assigning a Backup TFTP Server

TFTP Server 2 displays the IP address of the backup TFTP server. This server is used to obtain configuration files and software upgrades if the primary TFTP server is unavailable.

Before you can assign a backup TFTP server, the Alternate TFTP setting must be set to Yes.

This procedure does not apply to the Cisco IP Phone 7902G.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to TFTP Server 2.

Step 6 Press the Edit softkey.

Step 7 Use the buttons on the keypad to enter the new Alternative TFTP Server address, using the * key on the keypad to enter periods.

Use the Validat softkey.

Step 9 Press Save.

Configuring CDP

You can disable or enable Cisco Discovery Protocol (CDP). CDP allows the phone to be discovered by the CiscoWorks2000 network management system.

For more information about CiscoWorks2000, refer to the documentation available at this URL:

Using the Phone Configuration Web Page (Cisco IP Phone Models 7902G/7905G/7912G)

Step 1 Open the Phone Configuration web page.

a. Open your web browser and enter the following URL, where IPaddress is the IP address of your phone

b. Press Enter.

The Phone Configuration web page appears.

Step 2 In the pane on the left under Change Configuration, click Network Parameters.

You may be prompted to enter a password.

The Network Parameters web page appears.

Step 3 In the OpFlags field,

a. To enable CDP, change bit 6 to a zero (0).

b. To disable CDP, change bit 6 to a 1.

Using the Phone’s Network Configuration Screen (Cisco IP Phone Models 7905G/7912G)

Step 1 Press the Menu button.

Step 2 Use the Navigation button to select Settings, and then press the Select softkey.

Step 3 From the Settings menu, use the Navigation button to select Network Configuration, and then press the Select softkey.

Step 4 From the Network Configuration menu, press **#.

If your phone displays «Enter Admin Password,» enter your password and then press the Enter softkey.

Make sure that an unlocked padlock icon appears in the upper-right corner of your LCD.

Step 5 Scroll to CDP Enabled.

If CDP is enabled, the option appears as

Step 6 Press the No softkey to disable CDP.

Step 7 Press Save.

Источник

Adblock
detector